Beginner
How to Use a Cookie Press
How to use a cookie press: pick the dough, load the barrel, press clean cookies onto the sheet, then bake and clean up, step by step.
A cookie press works a lot like a caulk gun for dough: each squeeze pushes a measured amount through a patterned disc onto the sheet. Results depend less on strength than on three things, a dough the press can move, a barrel loaded without air gaps, and a clean press-and-lift on the baking sheet.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases.
What kind of dough goes in a cookie press?
Most cookie doughs are too stiff for a press. Spritz dough is the standard choice: buttery, soft and pliable, it moves through the disc and keeps its shape in the oven. Thin doughs such as sugar cookie dough also work, while doughs studded with chocolate chips or nuts clog the disc and should stay out.
Temperature is the usual catch, since cold dough resists the plunger and warm dough slumps. The cookie press dough thickness guide covers what soft enough feels like and how to fix dough that is too stiff or too soft.
Five steps to load the press
Loading takes a minute, and doing it carefully prevents most of the trouble later. Shape the dough into a log a little narrower than the barrel so it slides in without gaps. Designs vary, so check the maker's instructions for how your barrel opens.
- Unscrew the ring at the end of the barrel, the end opposite the handle.
- Slide in the log of dough, leaving some empty space at the handle end instead of filling the barrel to the top.
- Lay the disc you want flat inside the ring.
- Screw the ring back on until it is tight, with the disc sitting inside the barrel.
- Fit the plunger and push or ratchet it down until it just touches the dough and the air is pushed out.
Five steps to press a clean cookie
Once the press is loaded, the motion is short and repeatable. Use a plain, cool metal baking sheet with no grease or parchment, since the cookie has to cling to the sheet to leave the disc.
- Set the press upright with its base flat against the sheet, disc side down.
- Squeeze the trigger or turn the handle once, until a single cookie forms.
- Pause for about half a second, then lift the press straight up.
- Move over and repeat, leaving about 1 to 2 inches between cookies.
- Reload when the barrel runs low and keep pressing until the sheet is full.
Why do the first few cookies often fail?
The first few cookies are test cookies. Pressure inside the barrel takes a few squeezes to even out, so misshapen early ones can go straight back into the barrel. After that, the shape of each cookie tells you what to change.
- Tiny or incomplete shape: if your press has an adjustment, let out more dough per squeeze.
- Smashed, blurry pattern: adjust for less dough per squeeze, and expect each disc to need its own setting.
- Cookie lifting off with the press: the sheet is greased, lined or warm, so switch to a plain cool one.
- Uneven or patchy cookies: air pockets in the barrel, so repack the dough firmly.
- Dough that will not come out: it is probably too cold, so let it sit at room temperature briefly.
- Dough softening mid-batch: warmth from your hand on the barrel, so use one hand on the trigger and steady the sheet with the other.
Bake, cool and clean up
Pressed cookies are thin and bake quickly, usually around 350°F for 8 to 10 minutes until the edges are just golden. Follow the recipe's own time and start checking early. Let them firm up on the sheet for a minute before moving them to a rack, since they are fragile when hot.
Wash the press soon after use so dough does not dry in the discs. Take it apart, wash the pieces in warm soapy water, clear small openings with a brush or toothpick, and dry everything thoroughly. Dishwasher safety differs from maker to maker, so follow the instructions that came with the press. If disc sets and ease of cleaning are what you are weighing, see our recommendations on which cookie press for cheese straws to buy.