A burger smasher is a heavy, flat tool that presses a loosely packed ball of ground beef against a hot cooking surface. The pressure makes a thin patty with maximum contact, and that contact is what builds a deeply browned crust. Because the shaping happens on the griddle, there is no need to form patties in advance.
Beginner
How to Use a Burger Smasher
How to use a burger smasher for thin, crispy-edged patties: what to have ready, seven steps from hot pan to flip, and the mistakes that dry burgers out.
A burger smasher does one job, and it does it best in a single motion: it flattens a loose ball of beef against a very hot surface so the bottom browns hard before the patty has time to firm up. Most disappointing smash burgers come from heat and timing, not from the tool.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases.
The smasher shapes the patty on the griddle
Gather these before the pan heats up
Smash burgers cook in minutes, so everything needs to be within reach before the first ball hits the surface.
- Burger smasher: a heavy, flat press with a comfortable handle
- Cooking surface: a griddle, flat top or cast iron skillet that gets very hot
- Ground beef: 80/20 chuck, since very lean beef dries out fast
- Spatula: thin and stiff, for scraping under the crust
- Parchment paper: small squares, for when the press sticks
- Salt and pepper: ready to season right after the smash
- Buns and toppings: toasted and prepped, because the patties finish quickly
Seven steps from hot pan to flip
The sequence is short and the timing is what matters, so count from the moment the beef touches the surface.
- Heat the griddle, flat top or skillet over medium-high to high heat until it is very hot, close to smoking.
- Roll the beef into loose balls of about 2 to 3 ounces each, handling it as little as possible.
- Set a ball on the hot surface, leaving room between balls so the surface stays hot.
- Press straight down once, firmly, and hold for 2 to 3 seconds, until the patty is about a quarter inch thick or thinner. Do not twist the smasher, which tears the forming crust. If the meat sticks to the press, put a small square of parchment between them and peel it away right after.
- Season with salt and pepper right after the smash, while the patty is flat.
- Leave the patty alone for roughly 1 to 2 minutes, until the edges are dark brown and crisp.
- Slide the spatula under the crust, scraping to release it, and flip once. Add cheese now, and cook the second side for about 30 to 60 seconds.
Five mistakes that cost the crust
Nearly every failed smash burger traces back to a few habits, mostly about heat, fat and fussing with the meat.
- Pressing more than once: each extra press squeezes out juice and compacts the meat.
- Flipping too soon: a crust that has not set sticks and tears the patty apart.
- Using lean beef: low-fat meat turns dry fast at this heat.
- Cooking on low heat: without strong heat the patties turn thin and gray.
- Crowding the surface: too many balls at once cools it and slows the sear.
Pick a press that suits your pan and your hand
Weight, face size and grip all matter. Heavy presses, whether cast iron or thick stainless steel, do much of the pressing with their own weight, so less force is needed from the cook; lighter ones work, but the pressure has to come from the hand. A face wider than the pan leaves no room for a neighboring burger, while a smaller one lets two fit side by side, and a handle that stays comfortable near a hot surface makes the single firm press easier to control.
Care differs by model, so follow the maker's instructions. The Cuisinart Cast Iron Smash Burger Press calls for hand washing, thorough drying and a light coat of oil, and is not meant for the dishwasher, while the stainless steel Burger Iron Smash Burger Press 6 inch is listed as dishwasher safe.
See our recommendations on which burger smasher to buy.
Frequently asked
Can you use a spatula instead of a burger smasher?
Yes, a sturdy, flat spatula works, and pressing the flat side of a second spatula on top adds leverage. The trade is control: a smasher presses the whole patty flush, while a spatula can press unevenly at the edges, so expect to hold it a little longer.
How can you tell a smash burger is done?
Look for dark, crisp edges and, if cheese went on, a fully melted slice; a patty this thin is cooked through by then. Food safety guidelines put the safe minimum internal temperature for ground beef at 160°F, so check with a thermometer if there is any doubt.