Under-sink jobs turn annoying fast when one hand is on a pipe and the spare kitchen sink strainer stopper is in the garage. Gather these first.
Beginner
How to Install a Sink Drain Strainer
How to install a sink drain strainer: tools, a step-by-step basket strainer replacement, sealant choice and the mistakes that cause leaks under the sink.
Swapping a basket strainer is closer to a sealing job than a plumbing one. A leak-free result comes from a clean opening, an even rope of putty and a locknut tightened gradually, not from brute force. With the old assembly out, the work asks for patience under the sink more than for skill.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases.
What to have within reach before loosening anything
- Replacement strainer assembly kit
- Plumber's putty, or silicone sealant if the sink material calls for it
- Channel-lock pliers or a sink wrench
- Flathead screwdriver
- Putty knife or plastic scraper
- Bucket for water left in the trap
- Rags and a stiff sponge
Pick a strainer that fits the sink
Measure the drain hole before buying, or take the old strainer along as a model so the new one matches. The tailpiece has to suit the drainpipes as well, and a brass one lasts longer than most alternatives.
The kitchen sink drain strainer comparison covers drain fit, basket construction and materials across popular models.
Eight steps to replace a basket strainer
The sequence below runs from emptying the cabinet to testing the finished seal. Hand-tighten each connection first and use tools only to snug it.
- Clear the cabinet under the sink and set a bucket beneath the P-trap.
- Loosen the slip nut joining the tailpiece to the trap and let the trapped water drain.
- Unscrew the large locknut under the sink and lift out the old strainer, prying gently if old putty holds it.
- Scrape off the old putty, scrub the opening with warm soapy water and dry it completely.
- Roll plumber's putty into an even rope and press it around the underside of the new flange.
- Seat the strainer in the opening and press down until a little putty squeezes out.
- From below, slide on the rubber gasket, then the friction ring, then thread on the locknut and tighten it gradually.
- Wipe away the excess putty, reconnect the tailpiece and pipe, then fill the basin, release it and check every joint.
When putty is the wrong sealant
Plumber's putty can stain porous stone such as granite or marble, so a stone sink calls for a different approach. Check the sink maker's guidance first and use silicone sealant only if it recommends one.
Mistakes that cause leaks
Most failed installs trace back to a short list of shortcuts.
- Poor surface preparation, with old putty or residue left on the opening
- Leaving out the friction ring or stacking the bottom hardware in the wrong order
- Overtightening, which distorts the gasket and stresses the sink
Plumber or DIY
Replacing a strainer is generally a beginner-friendly repair when the existing plumbing is in reasonable shape and there is room to work under the sink. Badly corroded pipes, a cracked area around the drain opening or fittings that will not budge turn it into a larger repair, and a plumber is the better call.
The types of sink strainers that simply sit in the drain opening need none of this work, which makes them the easy route when only a basket is missing.
Frequently asked
Why does the strainer turn when the locknut is tightened?
The body has nothing holding it still once the putty is soft. Brace it from the top by wedging a tool through the crossbars of the basket while the nut is turned underneath, or ask a helper to hold it. The tool only supplies resistance so the body stays put.
Should the strainer be sealed with putty or silicone?
Putty never hardens, so a strainer sealed with it comes out easily years later. Silicone sets firm and is harder to undo, and it can suit porous stone better. When the sink material is in doubt, follow what the sink manufacturer says.