How-to

How to Clean a Meat Grinder

How to clean a meat grinder: bread pass, hand-wash steps, which parts can go in a dishwasher, motor care, and oiling parts to prevent rust.

A meat grinder is easiest to clean in the first few minutes after use, and hardest an hour later. Fat and meat residue crust over inside the head, the plate holes clog, and bare metal starts to rust once it stays damp. A short routine of one bread pass, hand washing, thorough drying and a film of oil keeps the machine safe and the blade cutting cleanly.

Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases.

Why the cleaning cannot wait

Raw meat leaves oil, grease and stray scraps behind, and they dry into a crust if left to sit. That residue is where bacteria such as Salmonella and E. coli collect, and it is also what leads to odors and rust. Cleaning straight after the last batch, while everything is still soft, is the single habit that makes the rest easy.

Eight steps to a clean grinder

Start before the grinder comes apart: push two or three slices of bread through the machine the way the meat went in, so the bread absorbs grease and carries out leftover bits. Then work through the parts.

  1. Unplug an electric grinder and take it apart.
  2. Separate the pusher, feed tube, auger, blade, plate and retaining ring.
  3. Scrape off any meat still clinging to the parts.
  4. Rinse every piece under hot running water.
  5. Wash each part by itself in hot, soapy water with a brush, working into crevices and plate holes.
  6. Rinse until no soap remains.
  7. Dry each piece right away with a clean towel.
  8. Wipe a light film of food-grade mineral oil onto bare metal parts, then wipe off the excess.

Keep the motor base out of the water

On an electric grinder, only the removable head parts go into the sink. The motor housing is wiped with a damp cloth and then a dry one, and never submerged or held under running water. A manual grinder has no motor, so it is usually quicker to clean, but the parts still need the same thorough drying.

For stubborn residue, a soft brush or a toothpick lifts it out of the plate holes. Sanitizing and abrasive or acidic home cleaners, such as baking soda paste or vinegar, suit some finishes and not others, so follow the maker's instructions before using them.

Which parts can go in the dishwasher?

Heat can damage some metal parts, and prolonged soaking can rust them, so the maker's statement decides. The listings for the models in this comparison disagree, which is why hand washing is the safe default. The meat grinder comparison for venison covers which models state that their blades and plates are dishwasher-safe.

ModelListed guidance
Aiheal Electric Meat GrinderNot for the dishwasher; wipe dry
Altra Life Electric Meat Grinder 2300WNo dishwasher or hot water
AAOBOSI #12 Heavy Duty Meat GrinderBlades and plates dishwasher-safe
Aaobosi Electric Meat GrinderBlades and plates dishwasher-safe; hand-wash advised
AAOBOSI 4-In-1 Electric Meat Grinder 2800WBlades and plates dishwasher-safe

Dry, oil and store to stop rust

Rust shows up on the plate and blade first, and it comes from leftover moisture. Finish with these habits:

Frequently asked

How often should I clean my meat grinder?

After every use. Residue left overnight dries hard and is the main cause of odors and rust, so a quick wash right after grinding is far easier than a deep clean later.

What kind of oil should I use on my meat grinder?

Food-grade mineral oil is the usual choice for bare metal parts. It is safe around food and does not go rancid the way many cooking oils do, so it will not leave a sticky residue. Apply a thin coat and wipe the excess.

How often does the blade need replacing?

There is no fixed schedule. Sinew and bone dull it fastest, so trimming meat well helps. When the grinder starts to struggle or the meat comes out mashed rather than cut, sharpen or replace the blade and plate according to the maker's guidance.