Beginner
DIY Fermentation Lids
DIY fermentation lids for mason jars: the parts you need, how to cut and seat an airlock, and when a ready-made lid saves effort.
The part of a fermentation lid that matters is small: a one-way route for gas to leave the jar. Everything else is a plastic cap, a grommet and a three-piece water airlock, and all of it can be put together at home with a drill. The catch is that a lid with a poorly cut hole looks finished and still lets air in.
Affiliate disclosure: As an Amazon Associate I earn from qualifying purchases.
What a homemade lid has to do
A fermentation lid has one real job: let carbon dioxide out without letting fresh air in. Air at the surface is what invites mold, so the lid works together with keeping the vegetables pressed under the brine. A cap that only seals tight is not enough, because a sealed jar builds pressure while the ferment is most active.
An airlock solves that by acting as a one-way exit for gas, which is also why it removes the daily burping that a plain lid demands. Whatever gets built at home has to do the same two things, vent and block, or it is only an ordinary cap with a hole in it.
What goes into a homemade lid
The common homemade version borrows from winemaking: a standard cap, a small water-filled airlock and a grommet that holds the two together. Metal canning lids are a poor base because they corrode over time in contact with brine, so a plastic wide-mouth storage cap is the usual starting point.
- Wide-mouth plastic storage cap that fits the jar you already own
- Three-piece water-filled airlock, the kind sold for wine and beer making
- Silicone or rubber grommet sized to the airlock stem
- Drill bit or hole punch matched to the grommet
- Water for the airlock reservoir
Seven steps to a working lid
The one step that decides whether the lid works is the hole. If it is cut too large, the grommet cannot seal and gas and air pass both ways; if it is too small, the grommet will not seat. Check the grommet maker's size before cutting, and practice on a spare cap if one is available.
- Choose a clean plastic wide-mouth cap and confirm it screws fully onto the jar.
- Mark the center of the cap and cut the hole to the size the grommet calls for.
- Smooth the cut edge so no sharp plastic remains.
- Press the silicone or rubber grommet into the hole until it sits evenly all the way around.
- Push the airlock stem through the grommet.
- Add water to the airlock reservoir, then fit the inner cap over the tube and the outer cap on top.
- Fill the jar with vegetables and brine, keep them below the liquid, and screw the lid on.
A drilled lid still needs a weight
An airlock keeps air out, but it does nothing to keep food under the brine. In the first days of fermentation, gas bubbles collect inside a tightly packed mixture such as shredded cabbage and push it upward, so a weight or similar holder is needed whether the lid is bought or built.
The water in the airlock also needs a glance now and then, because a homemade three-piece lid has the same upkeep as any store-bought one of its type: extra pieces to wash and a reservoir that can run low or take in brine overflow. Follow the maker's instructions for cleaning the plastic parts, since some kits warn against boiling water on them.
When a ready-made lid is the easier route
The build is worthwhile when a wine or beer supply store is nearby and the parts are already on hand. The drawbacks are the pile of small pieces to keep clean and a tall profile that makes jars harder to fit in a cupboard. Waterless silicone valve lids avoid both, and some store-bought kits bundle stainless wide-mouth lids with silicone rings, water airlocks and grommets, which is the same three-part design already assembled.
For models that match the jars and storage space in a kitchen, see our recommendations on which fermentation lids to buy.
Frequently asked
Do I need a fermentation lid?
No. Many people ferment sauerkraut under an ordinary jar lid screwed on slightly loose, with the vegetables held under the brine, and that costs nothing to try. A loose lid is not a true airtight setup, and it leaves the jar open to some air, so an airlock generally gives a more controlled result and takes away the burping routine.
Are airlock lids worth it for small batches?
Usually yes for anyone fermenting in wide-mouth jars they already own. The lid goes on, the airlock handles the gas, and nothing needs opening during fermentation. Because the lids are only used while the ferment is active, only as many are needed as there are jars fermenting at the same time.